Microtronik HexProg ECU klonavimo, Chip tiuningavimo įranga

850.00

HexProg patobulinta HexTag versija, sukurta taip, kad atitiktu visus jūsų lukesčius! Įranga naudotis nesudėtinga, dirba greitai, su HexProg bus vienas malonumas atlikti ECU klonavimo / Chip tiuningavimo darbus. DĖMESIO! Visos įrangos funkcijos yra NEMOKAMOS visam laikui, išskyrus ECU klonavimas, ECU klonavimą nuo aktyvavimo dienos suteiksime 30 dienų!

Pakuote sudaro:

1 x HexProg Programeris
1 x HexProg maitinimo modulis
1 x OBD2 kabelis
1 x Raktų programeris
1 x Key & EEPROM resetinimo adapteris
1 x MPC adapteris
1 x USB kabelis
1 x BDM & Jtag kabelis

Būsena: Užsakoma
Pristatymo laikas: 4-7 darbo dienos

Aprašymas

Kalbos: Anglų
Programinė įranga: HexProg
Operacinės sistemos: Windows 7, Windows 8, Windows 10
Atnaujinti įranga: Galima
Naudoti interneto ryšį: Galima
Garantija: 12 mėnesių
Gamintojas: Microtronik

On Bench Chip Tuning/Ecu Cloning:

You can read and write P-Flash, D-Flash, External Flash, and external EEPROM with the option of automatically checksum correction, you will have two methods in most of Ecus:

  • Factory mode: with this option you don’t have to open the Ecu cover. Just plug some wires for power and signals and you are ready to go.
  • Boot mode: Opening the Ecu is mandatory to connect the boot wire on the Ecu board. This method is useful when the Ecu is not responding.
    You can check Hexprog Ecu List – Here

OBD Chip tuning:

Hexprog starts supporting OBD functions in early 2021, It supports read/write the map area, (virtual read is supported too). It also includes important functions in some Ecus, like VIN Changing, Coding backup/restore and Fault codes read/erase.

Microtronik has a huge experience in all types of car Ecus flashing and coding, we deployed this experience in Hexprog to produce one of the safest programming tools by OBD.

BMW ISN reading:

We took the most important part from Autohex for ISN management and we adopt it in Hexprog.

With Hexprog you can read all long ISN from any BMW Ecu including the latest Bosch MG1/MD1 Ecus starting from 2005 up to today’s DME/DDE.

BDM read/write:

With Hexprog you are able to break the protection of immobilizers like CAS in BMW, EIZ/EIS in Mercedes Benz, BCM in Volkswagen and Porsche…etc.

We are proud that Hexprog is the only tool can read/write CAS4 without de-soldering or cutting any part from the board. The same in most of immobilizers.

Built in Editors:

With Hexprog you can edit many Flash data like:

Edit CAS3+ VIN, ISN and keys

Edit CAS4, CAS4+ VIN, and ISN

Edit mileage for BMW instrument clusters

Repair BMW FRM:

BMW E series has a serious problem with FEM, the data gets damaged easily.

With Hexprog you can repair the FRM 3 in one click.

Other functions:

You can reset mileage in protected EEPROMs like M35080, M35160, 080D0WQ, 160D0WQ, the process takes few seconds
You can do key reset for many brands like Audi, BMW, MINI, Porsche, Toyota, Fiat, Renault…etc.
Read/Write a wid range of SOP8 EEPROMs.
Works side by side with Autohex to make keys

Compare to Hextag:

Both Hextag and Hexprog have the same functions. The difference is in the hardware structure which may reflect the performance and the future added functions. Below table shows the major differences.

Feature Hextag Hexprog
Microprocessor Speed
100 MHz 220 MHz
External Memory
Not Available Available
USB Speed Full Speed (12Mbps) High Speed (480 Mbps)
Power Protection Good Perfect
Key coil
Internal External
Hardware Support For Future functions Almost will be supported
Sure will be supported